Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jpm

Pages: [1] 2 3 ... 7
1
Tweaking.com Programs & Site Help & Support / Re: Whats up.... :(
« on: January 09, 2018, 05:56:30 PM »
The repairs form 3.0 to 4.0 are essentially the same. The difference is in the pro features.  Did you run any of those? Or any of the tweaks after the fact?

2
Ok - checkdisk cant advise you to uninstall anything - so that must be something else?

Also, the tray icon cannot load if the program is uninstalled - so I suspect something else again.

To unload the tray icon click settings then uncheck the launch tray icon at program startup.

Then I would highly suggest doing some decent viral scans.


3
Tweaking.com Programs & Site Help & Support / Re: windows don't start up
« on: December 29, 2017, 07:36:17 AM »
The startup repair is actually a windows issue - not the Tweaking Repair program.  Did you run this in safe mode for our repairs? Becuase I suspect there was another underlying issue.

Either way this "should" get you back
https://www.youtube.com/watch?v=AkIGGE8hJpI

4
I've seen that happen before with driver issues and once with a boot sector virus - I'll assume it isn't that.

I found a really good article here that can help.

https://www.sevenforums.com/tutorials/139576-startup-repair-infinite-loop-recovery.html
.

5
Tweaking.com Programs & Site Help & Support / Re: Tweaking v1.0.0
« on: November 18, 2017, 10:12:40 AM »
I know you cant do it 100% with psexec but  it looks like this is how to do it with PDQ
https://www.pdq.com/create-pdq-packages/

6
I appreciate the panic - I've been there myself.

The MD5 Hash is a type of check to verify the integrity of our files.  If, when starting the program, the MD5 fails - then the copy you have is no good for some reason. It could be a hacked copy or a corrupt copy but either way, it should not be used. 

To fix that you just needed to redownload the program and reinstall.

Given the description, I'd wager you have a rather serious hardware issue - probably your drive.  If while running the program it locked up, crashed and I am assuming corrupted one f our files - bad hard drive makes sense.  It also makes a little sense if the Acronis then had issues. However, even if Acronis formats the drive you should still be able to lad the backup image on the machine. So that may be unrelated. I'd need to know more.

But I would check the drive for sure.




 

7
Registry bloat used to be a big issue but it's not as important as it used to be.

Basically, the registry is loaded into RAM on boot. The smaller the faster it loads.  I just looked mine add up to like 200+ MB.

If I were to clean and compress I suspect it would drop the size in half.  hence loading and looking things up would be faster.

Given that I have a lot of ram on this machine and it is fairly fast - the 100 MB savings would be a negligible difference -  But it would be a difference.

But I suppose the registry is like anything else - you should periodically clean it up. That said, if you simply run a cleaner the keys become "null" or zeros so typically if you look at a cleaned registry and compare it to the old one. They would be of similar size. Compressing the registry just rid of the nullness. (I made that word up :) )

8
per ashkinos:


PROBLEM: Addresses were printing way off target.

SOLUTION:
PostScript functionality is not included in my default (Brother) printer driver.
I had to go to the support page for my printer and install a second (PS emulator) driver to use when printing envelopes.

Thank you SO much for your help.
This software will help me for the rest of my life...so...yeah.
THANKS!

9
You compress the registry to reduce the size and hence system resources needed to use it.  Frankly, there is no point to "cleaning" the registry without compressing it.


It sounds like something stopped the compressor. The .new file is the compressed version.  It may not be complete -so don't use it. However if you rename that and re-run will it work?



10
Tweaking.com Programs & Site Help & Support / Re: Crashing
« on: October 26, 2017, 02:02:47 PM »
What mode is the reg backup running? Basic or Shadow copy?

11
Tweaking.com Programs & Site Help & Support / Re: Address Import
« on: October 25, 2017, 07:12:14 PM »
It's doing it to me too. Going to go fill Shane full of coffee and see if we can get a fix out.

12
Computer Help / Re: Find all duplicate names by pattern
« on: October 23, 2017, 08:04:53 AM »
from a command prompt?

You could do something like "dir *kl_76-KLK7L.jpg /s"   if I understand the issue.  The "*" is wildcard so that says, give me a list of all the files that start with anything and end with kl_76-KLK7L.jpg .. The /s searched all the subdirectories from where you are at.

or if you just wanted files with KL7L in it that ended with anything extensions

dir *KL7L*.* /s

But I would just use a program.  ;)
http://www.majorgeeks.com/files/details/alldup.html



13
Computer Help / Re: Lock account
« on: October 03, 2017, 04:08:08 PM »
Man, I haven't even heard of that before.... and I've heard a lot.  I suspect it is something else.  can you make a new account?
 

14
As we have said - and always said. We sell the product per version.  From version 3 to version 4 was about 3 years. So it's not like we are churning it out versions everyday.  With our new interface if you have purchased version 3 100% of version free features will work. We simply wrapped 3 and 4 into the same interface to maintain one code base.  If you do not need the v4 features you have a choice to simply stay with what you are doing for no cost.  If you upgrade to or purchas version 4 - when version 5 comes out you can expect the same thing.  This is nothing new in the shareware world. It's pretty much been like that since the dawn of shareware to some extent. 

We had no choice but to change the licensing agreements because large companies are literally ripping us off including the one that wrote the operating system that you are using.

The tech license is there to try and stay true to our concept - The repairs are free for those who need them. However, if you are using our product as billable hours, as gsfriend is,  then you should be charged a fair rate. $65 per tech seems more than reasonable, so we can keep maintaining and updating the product. Try and find a tech that will work for 65 per year. ;) 

I do appreciate that some do not agree with this licensing decision but like I said we had little choice.



15
You type the scripts you want in the window - then save as the current script.

After the repairs run the scripts run.

YOu can save different scripts, but the "current" is the one that runs.

Hope that helps.

Pages: [1] 2 3 ... 7