Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Thanks Boggin! I figured that but could you tell me what is the purpose of doing a backup of the reg, if it's better to use Restore point?
It's all in the WR I know and I am assuming that all programs have a purpose, so just wondering.
Also, the Reparse Points and Enviornment Variables states that this step is not a fix (Pre-scan) and can be skipped??? I think it is important and I run it every once in a while just to make sure everything is there where it should be.
I also believe you should add two other programs to WR:
Using Command Prompt (Adm) :
DISM.exe /Online /Cleanup-Image /CheckHealth
DISM.exe /Online /Cleanup-image /ScanHealth
DISM.exe /Online /Cleanup-Image /RestoreHealth
Dism.exe /Online /Cleanup-Image /AnalyzeComponentStore
Dism.exe /online /Cleanup-Image /StartComponentCleanup
Using DISM is important too to insure the PC is running tip-top.
Repair Windows 8/10 Component Store
The following commands are done.
Dism /Online /Cleanup-Image /StartComponentCleanup
Dism /Online /Cleanup-Image /RestoreHealth
The first command cleans up the component store (WinSxS Folder) in windows, reducing it size and removing old entries.
The 2nd command is used to repair corrupt files and corrupt entries in the component store.
Reasons for this repair:
Used to fix Windows component store corruption when a SFC /SCANNOW command is unable to repair corrupted system files because the store (source) is corrupted, then run the SFC command again.
Used to fix Windows component store corruption when the same Windows Updates continue to appear to be available to install even though they already show successfully installed in update history.
More information on these commands can be found here:
http://technet.microsoft.com/en-us/library/hh824869.aspx
and
http://www.eightforums.com/tutorials/26512-dism-fixing-component-store-corruption-windows-8-a.html
https://answers.microsoft.com/en-us/windows/forum/all/how-to-start-program-before-user-logon-windows-7/2bff97c4-c037-437c-9fa7-b143a3ae5189
Get-AppXPackage -AllUsers -Name Microsoft.MicrosoftEdge | Foreach {Add-AppxPackage -DisableDevelopmentMode -Register “$($_.InstallLocation)\AppXManifest.xml” -Verbose}it will spit out in yellow the verbose of what it does let me know
bcdedit /enumWindows Boot Managerlet me know if it says safeboot and network like how this looks.
--------------------
identifier {bootmgr}
device partition=\Device\HarddiskVolume4
path \EFI\MICROSOFT\BOOT\BOOTMGFW.EFI
description Windows Boot Manager
locale en-US
inherit {globalsettings}
default {current}
resumeobject {114ff4f3-701b-11e7-8577-a33ddabf8e12}
displayorder {current}
toolsdisplayorder {memdiag}
timeout 30
Windows Boot Loader
-------------------
identifier {current}
device partition=C:
path \Windows\system32\winload.efi
description Windows 10
locale en-US
inherit {bootloadersettings}
recoverysequence {114ff4f5-701b-11e7-8577-a33ddabf8e12}
displaymessageoverride Recovery
recoveryenabled Yes
isolatedcontext Yes
allowedinmemorysettings 0x15000075
osdevice partition=C:
systemroot \Windows
resumeobject {114ff4f3-701b-11e7-8577-a33ddabf8e12}
nx OptIn
safeboot Network
bootmenupolicy Standard