Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - ka6uup

Pages: [1]
I have a small 16 bit program I really like and have solved a lot of problems to get it to get it to run on windows 10. ( Humour me) ;-}}
However when I try to open the settings menu I get a VBRUN300.DLL error.
I think the issue is registration of the file and when i try to register it i am told it may not be compatible with the computer I am using (Windows 10 32 bit)
and to check if it is compatible with x86 or x64 regsvr32.exe.
Is there a way around this?

2 Support & Help / Restore Does Not Work
« on: October 09, 2019, 03:12:23 pm »
I have a Windows 7 Computer on which system restore does not work.
At first I thought I was doing something wrong but after going to Safe Mode and trying it there and searching for information on the web I came to the conclusion
it has never worked. It creates restore points but no matter what I do it will not restore to those points.
I was advised to boot and go to the repair option and do a repair but I am wary. I have tried that before and things have not gone well.
Has anyone ever run into this issue and what is the solution if any?

Up until a couple of days ago, I was able to access My Music, My Pictures, and My Videos folders  in My Documents under Libraries/Documents/
Now I am told "You don't current have permission to access this folder and refers me to the Security Tab in the Properties for each folder.
Since I don't have the knowledge to fool around with these settings, I decided to try running Windows Repairs Permissions repair.
I did so and it didn't fix it
So here I am.
what do I do next?

I bought a key for Windows Repair.
Because I could not access the internet on the computer I needed to install it on, I bought it on another computer.
Now I cannot enter the key.
Is it because I am trying to install it on another computer?

5 Support & Help / Codejock.Controls error
« on: May 25, 2018, 07:20:50 am »
I have a windows XP machine on which I am trying to run Windows Repair but when trying to start it, I get a "Component.'Codejock.Controls 8.2.0.ocx or one of its dependencies not correctly registered:a file is missing or invalid"

After running Windows Repair, when trying to run Malwarebytes I get a message " unable to start;unable to connect to service.
I went to services and tried to start the service manually but it would not start???
Malwarebytes was running fine prior to this.

7 Support & Help / VLC and Windows Media Player Won't Open
« on: December 24, 2017, 12:48:22 pm »
I have a Dell Latitude with Windows XP SP3.
I use it mainly to play audio and video.
Recently VLC and Windows Media player stopped opening.
If I disconnect the power supply and battery and press the
power buttons a few times and reconnect power, both programs
will open but only once. after closing them they will not open till I repeat
the power cycle.
I have tried everything I could find with Google and have run windows repair without success.
Any suggestions?
Thanks, Chuck

8 Support & Help / Windows Repair Pro Question
« on: May 26, 2017, 05:54:54 pm »
Is it possible to run Windows Repair Pro with out loosing personal settings

I tried to do a non-destructive repair as described by Fred Langa and now I cannot boot my computer. (I had done this in the past with no problem)
It does however boot into safe mode but when I tried to do a restore, there were no restore points shown.
I disconnected all the usb devices i have hooked up, and that seemed to change the point at which the stop takes place.
Thanks, Chuck

General Computer Support / Windows XP Explorer Acting Up
« on: March 17, 2017, 04:07:13 pm »
It started with Explorer (Not the web browser) not remembering it's position setting. it started opening in the lower right hand corner of the screen.
Then it started opening maximized. Now, most of the time, when closing it I get the error: "Proxy Desktop: explorer.exe - Application Error.
The Exception Unknown Software Exception 0x40000015 Occurred in Application at location 0x100891lda.
It still works but is an annoyance. Any help would be greatly appreciated.

11 Support & Help / pyLoad error
« on: October 07, 2015, 08:41:35 am »
I ran windows repair and now am receiving a pyLoad error:
pyLoad is not responding on http://127.0.0/1 /flashgot. Please check your firewall settings and the pyLoad configuration for the clock and load plugin. etc.
I can't even find pyLoad on my computer.
I am running windows xp.

Under Windows XP sp3, for reasons which I cannot explain, this problem began a couple of days ago.
I can get it to connect by doing a power reset of the WRT54G v5 router and then quickly doing a repair of the wireless connection before the router finishes booting up. This usually results in a connection.
Also, now, my wireless mouse doesn't work till I get it connected????
I ran the All In One repair item #12 "Repair Winsock and DNS Cache, but, that didn't fix it.
Can anyone suggest further steps to repair this?

General Computer Support / Cannot turn firewall on or off
« on: June 26, 2013, 05:05:06 pm »
I ran Windows repair and now when I try to access the firewall to turn it off I
get a message "due to an unidentified problem windows cannot display firewall settings"
I have run the "NETSH FIREWALL RESET" and the "Rundll32 setupapi,InstallHinfSection Ndi-Steelhead 132  and run windows Fixit 50203 all per Microsoft but non have worked.
Help would be appreciated.

Pages: [1]